6.jpg
8.jpg
Screenshot 2025-10-06 at 3.50.50 PM.png
6.jpg
8.jpg
Screenshot 2025-10-06 at 3.50.50 PM.png

1970-1981 Firebird Trans Am Camaro Premium Power Window Kit with Regulators and Motors by Nu Relics

$595.95

Complete Kit with Chrome Metal Switches!

Complete Kit with Chrome Metal Switches!

1970-1981 Firebird Trans Am Camaro Premium Power Window Kit with Regulators and Motors by Nu Relics

New complete power window kit for your 1970 - 1981 2nd Gen Firebird Trans Am or Camaro. Exact fit for all 70 - 81 models. Includes; both left hand and right hand regulators, both power motors, wiring harness, rubber door jam boots, and hardware.

This set comes with the Chrome Metal Premium Style Console Switch. (Exactly what we use in our Pro-Touring Builds)

  • Faster Window Engagement

  • Smoother Transitions

  • Better Weather Seal

~~NOTE: This is not a universal cheap imported power window kit. This kit is specifically made for your 2nd Gen Firebird right here in the USA! Please double check your options as each kit is especially made for you and are non-refundable.

Kit includes: 2 regulators (left & right side), 2 new ACI motors, complete wire harness, metal switches, and conduit to protect the wires going thru the door.

  • New ACI Motor AMP Draws

    No Load amps 3 / Low Load amps 5 / High Load amps 11 / Stall amps 20

    ACI Motors are Reverse Polarity

    This means that the ground for the system must come out of the master switch. There are 2 poles on the motor - to make it operate, you must put power to one side then ground to the other side - NOT to the motor case. This will result in the motor turning in one direction. By swapping the wires from side to side, the direction will change.

    Fuses or Circuit Breakers - 30 AMP

    Most of our harnesses will come with an in-line 30 AMP fuse. If you prefer, a circuit breaker will work too.

    You can hook your windows up to a varity of different power sources.

    Some options are: Straight to the battery (Windows should not have any battery draw when not in use).

    Find extra slot in fuse panel - tie in using the supplied fuse.

    Pull power from the key-on side of the switch

    Relays

    In most cases, you will not need to use a relay to boost amperage to the motors. The switches and wiring we use can handle the amp draws.

    If you are using old style 3 pole switches, a special relay is needed to reverse the polarity at the motor. These do not increase amperage, they just swap the ground from side to side. we have these available (prewired). Call us at 336-699-8949 for assistance.

    Grease & Oil

    1. On the regulator gear teeth and roller tracks, we recommend using a high temp automotive wheel bearing and chassis lubricant. NLGI grade 2 is one option

    2. Avoid the older soap based lithium grease - it sets up hard in cold weather making the windows harder to move

    3. A few drops of light weight oil in the pivot points will allow the Bronze Oilite ® bushings to work smoothly and reduce wear.

    4. On fuzzy runs and weather stripping - some 3M Silcone spray can help with break in

    5. Use Die-Electric grease or Tuner Lube on all terminals and connections. This protects against moisture and corrosion.

  • MODEL SPECIFIC - bolt into original mounting holes
    Uses Stock Channels
    Works with the curved glass of the 1960's and 1970's

    New ACI Motors
    Regulators are made on 1018 cold roll steel
    Bronze Oilite® thrust bearings at pivots (Made in USA) to keep them lubricated
    4130 Heat Treated gear plates for longer tooth life and better wear

    Lifetime warranty (Warranty requires copy of sales receipt or invoice.)